Large eddy simulation of a 660 MW utility boiler under variable load conditions

Large eddy simulation (LES) has become a promising tool for pulverized coal combustion with the development of computational fluid dynamics (CFD) technologies in recent years. LES can better capture the unsteady features and turbulent structures of coal jet flame than Reynolds averaged Navier Stokes (RANS). The coal-fired power plants in China are now required to be operated in a wide load range and quickly respond to the electric grid. The boiler performance of variable loads should be evaluated in terms of flow, heat transfer, and combustion processes. In this paper, LES was applied to simulate a 660 MW ultra-supercritical boiler under BMCR (boiler maximum continue rate), 75%THA-100, and 50%THA-100 conditions. The predicted gas velocities agree well with the thermal calculation and the temperature error is less than 130 K. The simulation results show that the operation load has significant effects on the boiler performance. It is also proved that LES can provide guidance for the design and operation of advanced coal-fired boilers.     

Formation mechanism of porous reaction-bonded silicon nitride with interconnected pores in the presence of MgO

In porous reaction bonded silicon nitride, whiskers normally grow in globular clusters as the dominant morphology and deteriorate the pore interconnectivity. However, the ceramic microstructure was significantly transformed with the addition of MgO; specifically, the morphology was modified to a combination of matte and hexagonal grains. Microstructural observation along with thermodynamic studies suggest that MgO interfered with the presence and nitridation of SiO_(g). Consequently, rather than being involved in the whiskers’ formation, surface silica instead reacted with volatile MgO to form intermediate products. Through these reactions, whisker formation was blocked, and a porous interconnected structure formed which was confirmed by 3D tomography. After heat-treatment at 1700 °C, β-Si₃N₄ crystallized in a glassy matrix containing magnesium. Resulting samples had an open-pore structure with porosity of 74–84 vol. %, and density of 0.48-0.75 g.cm^?3. Combination of high porosity and pore size of <40 μm led to compressive strengths of 1.1–1.6 MPa.     

超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性

针对100 mm超厚板TC4钛合金电子束焊接接头，采用慢应变速率拉伸方法评价接头在人造海水中的应力腐蚀敏感性，分析接头的显微组织和断口形貌，对接头的腐蚀机制进行研究. 结果表明，室温条件下应变速率为ε=1×10-6 s-1时，母材在海水中未表现出应力腐蚀敏感性；焊缝上部、中部和下部具有轻微应力腐蚀敏感性. 焊缝在海水中发生阳极溶解，产生氢吸附，导致裂纹的萌生. 同时氢扩散诱导α'相界及α'相内发生位错塞积，进而使裂纹在更低的应力水平下发生扩展.     

Effect of the annealing procedure and the molecular weight on the crystalline phase morphology and thermal properties of polylactide

The thermomechanical properties of poly(lactide) (PLA) are strongly related to its semicrystalline microstructure and morphology. Thermal annealing is a strategy to improve the crystallinity of PLA. However, the different techniques and specimen types needed for each kind of characterization could lead to misleading conclusions. In this work, annealed samples of three PLA grades with different molecular weights were studied by DSC, wide angle X‐ray scattering and polarized optical microscopy (POM) and the results are related to their thermomechanical and impact properties. Special focus is put on the POM results obtained by different approaches and the suitability of each of them to be related to the thermomechanical properties. By annealing medium molecular weight PLA specimens at 140 °C an important increase of the heat distortion temperature was obtained, which was not related to the spherulite size but to the combination of high crystallinity degree together with high α/α′ crystal type ratio. However, the impact properties of annealed PLA decreased with increase in the annealing temperature according to an increment in crystallinity and in the α/α′ crystal ratio. © 2019 Society of Chemical Industry     

High strain rate compressive response of the Cf/SiC composite

Carbon fiber reinforced ceramic owns the properties of lightweight, high fracture toughness, excellent shock resistance, and thus overcomes ceramic's brittleness. The researches on the advanced structure of astronautics, marine have exclusively evaluated the quasi-static mechanical response of carbon fiber reinforced ceramics, while few investigations are available in the open literature regarding elastodynamics. This paper reports the dynamic compressive responses of a carbon fiber reinforced silicon carbide (C_f/SiC) composite (CFCMC) tested by the material test system 801 machine (MTS) and the split Hopkinson pressure bar (SHPB). These tests were to determine the rate dependent compression response and high strain rate failure mechanism of the C_f/SiC composite in in-plane and out-plane directions. The in-plane compressive strain rates are from 0.001 to 2200?s^?1, and that of the out-plane direction are from 0.001 to 2400?s^?1. The compressive stress-strain curves show the C_f/SiC composite has a property of strain rate sensitivity in both directions while under high strain rate loadings. Its compressive stiffness, compressive stress, and corresponding strain are also strain rate sensitive. The compressive damage morphologies after high strain rate impacting show different failure modes for each loading direction. This study provides knowledge about elastodynamics of fiber-reinforced ceramics and extends their design criterion with a reliable evaluation while applying in the scenario of loading high strain rate.     

高温工作InAlSb的MBE生长及器件性能研究

接近室温的更高工作温度是第三代红外探测器发展的重要方向。本文论述了用MBE在InSb(100)衬底上外延生长制备P-i-N型三元In1-xAlxSb薄膜合金材料,并通过制备单元器件进行了验证。采用RHEED振荡和X射线双晶衍射对In1-xAlxSb薄膜的Al组分进行了调控和检测。5.3 μm厚薄膜的FWHM≈50 arcsec,Al组分约1.9%。10 μm×10 μm原子力表面粗糙度RMS≈0.6 nm。制备的单元器件获得了预期的理想效果,为下一步面阵焦平面的制备奠定了基础。     

Biosynthesis of silver nanoparticles in collagen gel improves their medical use in periodontitis treatment

Silver nanoparticles (AgNP) suspensions were biosynthesized by silver ions reduction in the presence of collagen, a nontoxic, organic polymer, intending to improve their medical use in periodontitis treatment. Spectrophotometric measurements showed a time- and concentration-dependent increase of AgNP formation in each suspension variant. Transmission electron microscopy revealed spherical morphology of AgNP in collagen and their mean diameter size was around 30?nm. The particle size distribution and zeta potential values of AgNP in collagen were determined by dynamic light scattering measurements. The surface charge of AgNP in collagen was positive, while commercial AgNP stabilized in citrate had negative surface charge. In vitro cytotoxicity testing of AgNP in collagen showed that they were biocompatible with human gingival fibroblasts in a wider range of concentrations than commercial nanoparticles. The antibacterial activity of AgNP in collagen against two pathogenic strains present in the periodontal pocket was dose-dependent and higher than that of AgNP in citrate. All these results demonstrated that AgNP prepared in collagen gel had improved properties, like small diameter, positive surface charge, high biocompatibility in human gingival fibroblasts, efficiency against bacterial growth and, thus, better therapeutic potential in periodontal disease treatment.     

300M超高强钢在中性盐雾环境中的腐蚀行为及机制

摘要：为了研究300M超高强钢在中性盐雾环境中的腐蚀行为及腐蚀机制，采用失重法，宏观、微观腐蚀形貌分析，三维表面轮廓分析及电化学分析的研究方法，来表征腐蚀实验现象并进行分析。结果表明：300M超高强钢在中性盐雾环境中的腐蚀产物为FeOOH、Fe2O3、Fe(OH)3和Fe3O4；腐蚀速率随着腐蚀时间逐渐降低，腐蚀后期（72h）腐蚀速率降低50%；腐蚀初期以点蚀为主，点蚀坑通过横向扩展，逐渐发展为后期的均匀腐蚀，腐蚀表面形貌呈沟壑状；外腐蚀层对基体的保护能力很弱，Cr元素在锈层靠近基体的一侧偏聚使内腐蚀层具有一定的抗腐蚀性。     

Fabrication of high-purity HfSi2 powder via molten salt-assisted magnesium thermal reduction

In this work, high-purity HfSi₂ powders were successfully fabricated via a molten salt-assisted magnesium thermal reduction method using HfO₂ and Si as raw materials. The effects of reaction temperature and time on the formation of HfSi₂ were systemically investigated. The morphological and phase composition of as-prepared HfSi₂ powders were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and nitrogen/oxygen determinator. The results indicated that as-obtained HfSi₂ powders possess the orthorhombic structure with approximately 6.4 μm in size and the oxygen content as low as 0.20%. This work can provide a novel route to fabricate the high-purity transition metal silicides powders.